INTRODUCTION
Insulation closed cell tube and sheet insulation is a flexible and lightweight elastomeric material designed for insulating liquid cooling and heating pipelines. The closed cell structure of Insulation provides many advantages over most rigid insulations such as:
• Moisture and vapor resistance without using additional vapor barriers.
• Stable thermal conductivity (K. value / value) throughout service life, due to its dense surface skin and closed cell characteristics.
• Flexibility which makes installation work easy and neat. Outstanding ultraviolet and weather resistance.
Insulation is an ideal insulation for frost control on sub-zero piping. It prevents heat gain and condensation problems on chilled water and refrigerant pipelines, and it also prevents heat loss from hot water plumbing, liquid and dual temperature piping.
AEROFLEX-HT
FOR HIGH TEMPERATURE APPLICATON UP TO +150 ºC
AEROFLEX-HT is an EPDM based closed cell light weight elastomeric thermal insulation specifically designed for solar and steam heating applications with service temperature up to +150 ˚C. AEROFLEX-HT has excellent ozone, UV and weather resistance properties suitable for outdoor applications. However, for outdoor installation with long term direct contact to sunlight, protective coating or jacketing are recommended. The flexibility of AEROFLEX – HT enables quick and easy installation on bent or irregular piping. AEROFLEX – HT is self-extinguished and does not melt when burnt.
AEROFLEX CONTINUOUS TUBE
AEROFLEX CONTINUOUS TUBE
USED IN SPLIT-TYPE AIR-CONDITIONING
Aeroflex Continuous Tube is especially designed for copper tubes used in split-type air-conditioning. It can be applied on the long and continuous copper tubes. Moreover, Aeroflex Continuous Tube made of the same material as Aeroflex tube. Installation is easy and saves cost without cuts and joints. It still maintains high quality standard of EPDM advantages.
- • Closed cell structure. Many sizes are available to fit the copper pipes
- • Low thermal conductivity.
- • Low water absorption and low vapor permeability.
- • Low smoke and toxic gases.
- • Excellent UV and weather resistance.
- • Non-corrosive on copper and stainless pipe s.
- • Non-polar.
- • Powder applied from factory.
AEROFLEX- SAPT
AEROFLEX WITH SELF-ADHESIVE TAPE, PROTAPE COVERED
Advantages:
- • Fast – through easy & time saving 3-step installation
- • Safe – due to the self-sealing property of PROTAPE
- • Clean – by eliminating the need for glue & brush
AEROFLEX-EP
FM APPROVED
AEROFLEX-EP is an EPDM based closed cell elastomeric thermal insulation specially formulated to meet Factory Mutual Approvals. FM has approved AEROFLEX-EP that it will not contribute significant fire according to FM fire test methods: UBC 26-3 Room Fire Test and Factory Mutual Approvals Full Scale Horizontal Simulated Pipe Chase Test. AEROFLEX-EP elastomeric thermal insulation tube and sheet are used to save energy and prevent condensation on chilled water and refrigeration system. They also efficiently reduce heat flow on hot water plumbing, liquid heating and dual-temperature piping.
AEROFLEX-FO
CLASS O
AEROFLEX-FO is a special polymer based closed cell elastomeric thermal insulation especially developed to meet BS Flammability Standard. Aeroflex-FO is classified as Class O which means having low fire propagation (BS 476 Part 6) and low flame spread (BS 476 Part 7).
AEROFLEX- STANDARD
WIDELY USED TO SAVE ENERGY AND PREVENT CONDENSATION
AEROFLEX standard is an EPDM based closed cell light weight elastomeric thermal insulation specially formulated to meet UL 94 V-0, ASTM E 84, Class 5.3 EMPA (Switzerland), IMO (International Marine Organization) and other international fire standards.
Aeroflex standard sheet and tube elastomeric thermal insulation are widely used to save energy and prevent condensation problem on chilled water and refrigeration systems. They also efficiently reduce heat flow on hot water plumbing, liquid heating and dual temperature piping.
AEROFLEX-HF
HALOGEN FREE THERMAL INSULATION
AEROFLEX-HF is halogen-free elastomeric thermal insulation especially developed for high standard with requirement of very low halogen content and very low corrosive acid gases from combustion. AEROFLEX-HF is formulated with very low chlorine and bromine content. AEROFLEX-HF is used for heating and cooling piping, tanks and air ducts, and to prevent stress corrosion with stainless steel pipe in the electronic control room, computer center, hospitals, laboratory, ships, trains and other areas where non-halogenated chemical materials are required.
.
AEROFLEX TWIN TUBE
AEROFLEX TWIN TUBE
AEROFLEX-Twin Tube is Aeroflex’s specially designed tube insulation for high temperature applications in solar energy and solar heating systems. It can be easily installed both indoor and outdoor with excellent UV and weather resistance. AEROFLEX-Twin Tube provides very stable thermal conductivity value throughout service life with low water absorption and vapor transmission.
CELFLEX-NV
CELFLEX-NV
CELFLEX-NV is a high quality synthetic rubber insulation ideal for split-type air-conditioning refrigerant piping. CELFLEX-NV is highly flexible and can be easily installed on irregular bent piping. It also provides very low thermal conductivity, thus it saves electricity consumption and prolongs lifespan of the compressors.
AEROFLEX-SSH
SANITARY, SOLAR AND HEATING TECHNIQUES
10 Important Properties and Advantages
-
- • high quality synthetic elastomer (EPDM based ) with complete closed-cell structure
- • excellent UV resistance.
- • CFC-free and PVC-free product.
- • high weather and ozone resistance.
- • up to 175ºC (347º F) operating temperature.
- • remains flexible in -40º C conditions.
- • lambda value (AR) 0.040 at +40ºC
- • self-extinguishing, no fireball drops, limited flame spread.
- • no copper and stain less steel corrosion (DIN 1988/part 7.)
- • < 5 ppb nitrosamine con tent.
Aeroflex-SSH is a new. flexible high-temperature insulation material which is applicable in the fields of sanitary, solar and heating. Aeroflex-SSH has excellent UV and weather resistant properties. Aeroflex-SSH is CFC and PVC free. Aeroflex-SSH remains flexible at temperature as low as -40º C. This property is important to make installation work fast and easy. This fact is an advantage that most users should not overlook. Aeroflex-SSH is self-extinguishing, does not release fireball drops and does not spread fire. The inner surface of Aeroflex-SSH tube is covered by talc powder which makes the installation work much easier. Aeroflex-SSH is also available with slit lengthwise together with self-adhesive tape and protape.
AERO-ROOF
ROOF INSULATION SYSTEM
AERO-ROOFTM is an insulation sheet laminated with aluminum foil and reinforced fiber. It is a lightweight insulation installed under the roof of the buildings to prevent heat from sunlight. Aero-roof is a thermosetting material which is made of special synthetic rubbers mixed with flame retardants, making it non-melt and non-flame spread when burnt.
• Heat, Water and Moisture Protection
• Non-flammable
• Non-fibrous and Odorless
• Heath safty and Environment friendly
• Easy Installation
AEROCEL-D/AL
CLOSED CELL INSULATION FOR HVAC AIR DUCT SYSTEMS
It is conventionally though that air ducts and associated equipment are insulted to prevent condensation, save energy and reduce noise, despite the fact that indoor air quality and public health should also be concerned when selecting an appropriate insulation for insulating on the equipments. Aeroflex-DI/AL with aluminum foil surfaced help minimizing mold growth. In addition, Aeroflex-DI/AL is non-fibrous & non-formaldehyde contents that do not vitiate the indoor air quality Aeroflex-DI/AL is closed cell light weight nitrile elastomeric thermal insulation.
It provided many advantages over mast fibrous, rigid or semi-rigid thermal insulation such as :
- • High resistance to mold & mildew growth
- • Air flow erosion resistant can be installed on internal and external duct surfaces.
- • Stable low thermal conductivity
- • Low water vapor transmission
- • No additional jacketing is required
- • Excellent flexibility and availability in self-adhesive makes installation work easy & speedy
- • Easy to clean, neat appearance with reinforce aluminum foil on the surface
PID
PHENOLIC COMPOSITES DUCT SYSTEM
Double-side aluminum foil The material of closing-cell rigid foam plastics is made form phenolic resin and emulsifier, curing agent, foaming agent and other auxiliaries and many other kinds of substances and represhing foaming curing. Its material itself has very low thermal conductivity coefficient, good insulation performance, low smoke, low-toxic and excellent heat-resistance etc.
Meanwhile PID double-sided aluminum foil phenolic composites duct inside and outside surface are composite of metal foil composite layer with special craft and phenolic resin, becoming the leading product in field of composite duct.
Single side color steel This product is a upgraded product based on PID double-sided aluminum foil phenolic composites duct. Outer is color steel plates and inner is compound aluminum foil. Not only inherited the excellent insulation performance and other advantages of PID double-sided aluminum foil phenolic composites duct, but also has high strength and advantage of color steel, becoming a new generation of duct product model.
AERODUCT
FLEXIBLE ALUMINUM AIR DUCT
AERODUCT is a fully flexible compressible extendable aluminum air duct. It is made of 2 ply double facing aluminum polyester foil bonded together with quality adhesive and reinforced with high carbon corrosion Proof spring wire. Aeroduct is non flammable which is ideal for residential and industrial applications.
AEROSEAL
ADHESIVE FOR AEROFLEX INSULATION
AEROSEAL is a Modified Neoprene Contact Adhesive specially formulated for bonding Aeroflex Insulating Materials firmly together. Also, ideal for use with other materials like Metal (painted/ unpainted ), Cork Board. Polyurethane Foam Rigid PVC’ Sheet, Formica, and Melamine Board and Rubber Sheet. The high water vapor resistance and good weathering properties of AEROSEAL can prevent water or moisture from penetrating through the joining points. AEROSEAL is able to form a strong, firm and permanent bonding between the applied materials providing long lasting service.
AEROBOND
POLYCHLOROPRENE CONTACT ADHESIVE FOAM AND FIBERGLASS INSULATION ONTO METAL SHEET
AEROBOND is a modified Polychloroprene Contact Adhesive specially formulated for attaching elastomeric foam insulation (such as Aeroflex & Aerocel) and fiberglass insulation onto metal sheets used in air ducting system. The strong bonding strength of Aerobond can easily hold up 4 kgs./m2 of insulation materials onto metal sheets at temperature of up to 93°C.
AEROCOAT
PURE ACRYLIC EMULSION PAINT FOR AEROFLEX INSULATION
AEROCOAT is a water based paint formulated with selected pure acrylic emulsion mixed with other special chemicals. Excellent for coating especially onto Aeroflex Insulation surfaces giving greater protection against ultraviolet rays or other adverse weathering conditions. Having elongation properties of more than 400% and with good adhesion promotor, AEROCOAT can stay very firmly and permanently to the coated surface without any problems of peeling . Its superb flexibility ensures no cracking even if the coated insulation surface is squeezed or compressed. With additional characteristics including fungus resistance, AEROCOAT is an ideal quality protective paint which can perform very efficiently both as decorative and protective insulation coating. Whether coated indoor or outdoor, AEROCOAT will be able to provide a smoothing aesthetic appearance while acting as a durable protective shield which can last for more than 10 years. Available .in shades’ of ‘white, blue green and black. AEROCOAT can be painted onto pipe Insulation surfaces giving easy Identification of the different Pipe functions.
PROTAPE SOFT JACKETING
Protape Soft Jacketing is used to covered insulation surface with following advantages :
- • Prevent scratches and other external damages
- • Good resistance to sharp objects
- • Prevent water and moisture penetration
- • Easy to install with time and costs saving
- • Easy to install with adhesive backing
- • Can be fabricated into irregular shapes
- • Easy to clean
ALUMINIUM SOFT JACKETING
ALUMINIUM SOFT JACKETING
is a special product for insulation surface protection. The outer surface is made of aluminium foil covered with 4 layers of Protape, making it excellent for UV resistance. The appearance is neat and smooth with excellent durability. It’s easy to install with time and costs saving. The soft jacketing comes with adhesive backing and can be pressed firmly on the insulation surface. It can also be fabricated into irregular shapes to meet various demands.
EVERSEAL
PIPE INSULATING CORK TAPE
EVERSEAL Cork Tape is designed to insulate all kinds of cold pipes including residential and automotive air-conditioners, freezers and refrigerators. It helps to prevent condensation problems and energy loss in cold and hot piping. Everseal can be applied as effective sound dampening and gasket materials. Everseal insulation tape sticks to all kinds of dry metals. It seals tightly without drying. It is flexible and does not shrink nor melt within the service temperature of -20 °F (-29 °C) to + 200 °F (+ 93 °C ).
ALUTAPE
SELF-ADHESIVE ALUMINIUM
ALUTAPE is a specially formulated solvent base pressure sensitive acrylic adhesive aluminum foil tape. Excellent for use as vapor sealing of fiberglass duct boards and sheet metal ducts. Ideal for use as masking material or for sealing purposes on any dry clean surfaces.
AEROTAPE
THE HIGH QUALITY SELF ADHESIVE INSULATION FOAM TAPE
AEROTAPE is the flexible and self-adhesive insulation foam tope which is mode from the some elastomeric material as AEROFLEX Closed Cell Insulation. Ideal for wrapping hot or cold pipings and fittings. Energy saving and very easy to use. Excellent for preventing condensation problems. Designed specially for retarding heat loss in hot pipings and preventing heat gain or frost formation on cold, chilled water pipings or refrigeration lines. Adheres firmly to all metals. No problem of delamination. AEROTAPE is specially coated with selected acrylic pressure sensitive adhesive providing long service life.
AEROFIX
PIPE HANGER AND SUPPORTER WITH SELF-SEALING TAPE
AEROFIX is a polymeric rigid foam hanger with rubber foam tape inner-lining, which absorbs vibration of operating pipelines. High density rigid foam makes Aerofix superior for supporting metal pipe weight. The outer cover consists of flame retarding rubber tape, which seals the hanger completely after installation in order to prevent moisture penetration and condensation problems
AEROSTAND
RUBBER LOAD SUPPORTER FOR AIR-CONDENSING UNITS
AEROSTAND made from natural rubber blended with EPDM synthetic rubber is a load supporter especially designed for air- condensing units. This stand possesses both high compressive strength and good weathering resistance. AEROSTAND can withstand loads of up to 60 kgs. per piece. Easy to install with bolt & nut prefixed. Very effective in reducing vibration and noise level. Reduced vibration helps prolong service life of the air condensing unit
AEROFIT
INSULATING FITTING COVERS
AEROFIT insulating Fitting Covers are designed for insulation warm or cold piping fittings and elbows without the need to field-fabricate into particular shapes. It help to save time and installation costs. Aerofit is very good in weather resistance without any protective cover required for outdoor application.
AEROFLANGE
FOR SQUARE DUCT CONNECTIONS
AEROFLANGE is a self-adhesive flange cover for square duct connection. It is made of the material as AEROFLEX thermal insulation the features the same excellent physical and technical insulation properties. It is the all-in-one ducting work solution that provides clean and fast installation with professional appearance.
Advantages:
- Clean and time saving installation
- The same excellent insulation properties as AEROFLEX
- Professional look and neat appearance
AEROPAD
ANTI-VIBRATION RUBBER PAD FOR CONDENSING UNITS
AEROPAD anti-vibration Rubber pad will
- • Reduce noise of machines
- • Stand outdoor applications
- • Reduce vibration to the floor
- • Be available in 1 meter length for universal use
- • Good weather resistance
- • Be available in small pieces with a hole for bolts
- • Not absorb water
ESCO CONDENSER BRACKET
THE LASTEST INNOVATION IN WALL TYPE SUPPORT FOR CONDENSING UNIT
ESCO CONDENSER BRACKET Made of pressed electro- galvanized metal sheet , with extra corrosion proof epoxy powder coating. This enables the bracket to be an all weather resistant product. Vibration is kept at a minimum by use of rubber pads included in the set. Easy to install with slide adjustment mechanism for any model of residential Air-condensing unit. 2 model s with loading capacities of max. 60 Kgs. & 80 kgs.
ESCOTAPE
SELF ADHESIVE FOAM GASKET TAPE FOR AIR-DUCT FLANGE CONNECTION
ESCOTAPE is an elastomeric closed cell self-adhesive gasket foam tape for cooling and heating air duct joint connections to prevent air leakage, reduce vibration and noise, serves as thermal insulation to prevent condensation and heat transfer. Escotape is laminated with acrylic pressure sensitive adhesive and can be easily installed on surface of connection joints.